When a pylon sign makes sense
If your building sits back from the road, shares a center with other tenants, or depends on drivers spotting you before the turn, a pylon often does more than any wall sign can. Pylons can carry one brand or stack several tenant panels, and where code allows they can include an electronic message section. On South Florida's wide commercial roads, height and early visibility are often the difference between a customer turning in and driving past.




Common pylon configurations
- Single-pole pylons - a sign cabinet on one steel pole, often with a decorative pole cover.
- Double-pole pylons - wider cabinets on two supports for larger faces.
- Multi-tenant pylons - stacked tenant panels so a center can change tenants without rebuilding the sign.
- Pole covers and architectural wraps - aluminum cladding that hides the steel and matches the building.
- Face and panel replacements - new faces in an existing cabinet for a rebrand or a new tenant.
Engineering, permits and wind load
A pylon is a structure, so it is engineered, not just drawn. Miami-Dade and Broward are in the Florida Building Code High-Velocity Hurricane Zone, and Palm Beach County has its own wind requirements, so foundations, steel sizes and connections are specified on signed and sealed drawings. Local zoning limits height, sign area, setbacks and spacing from other freestanding signs, and those limits change from one city line, and sometimes one road, to the next.
We handle the whole package in-house: drawings, engineering coordination, landlord approval, zoning and building review, electrical permits for lit cabinets, utility locates before we dig, and every inspection. Learn more on our sign permits page.
How we build a pylon sign
- Survey - confirm location, setbacks, sight lines, underground utilities and power.
- Design and engineering - elevations plus structural engineering for wind load.
- Permits - zoning and building review, then electrical.
- Foundation - excavation and concrete per the engineered design, with inspection.
- Fabrication - cabinet, faces, pole cover and LED lighting built in our Doral shop.
- Installation - steel and cabinet set, power connected, final inspection and closeout photos.
Materials and lighting
Typical pylons use a steel structure, aluminum cabinets and cladding, and polycarbonate or acrylic faces lit by LEDs. Polycarbonate resists impact better, which matters for large faces in storm country. LEDs use less power than the fluorescent tubes in older cabinets and are easier to service. If your existing pylon is structurally sound, a face change or an LED retrofit may make more sense than a new sign; see sign repair.
What affects the timeline
Pylon schedules depend on zoning review, whether a variance or design review is needed, engineering, foundation inspection, utility locates, power to the sign, and the size of the cabinet. Replacing faces in an existing cabinet is usually much simpler than a new structure. We set expectations after the survey.
What we need from you
- Site address, photos and the location you have in mind.
- A site plan or survey, if available.
- Your logo files, or tenant artwork for multi-tenant signs.
- Landlord or center sign criteria, and whether an old sign must come down first.
Where we work
From our shop in Doral we build and install pylon signs across Miami-Dade, Broward and Palm Beach counties, including Miami, Doral, Hialeah, Fort Lauderdale, Boca Raton and West Palm Beach. See our full South Florida service area.
Related services
- Monument signs
- Channel letter signs
- Sign installation
- Sign repair and LED retrofits
- Sign permits
- National sign partner program
Frequently asked questions
Can I put a pylon sign anywhere on my property?
No. Zoning controls where freestanding signs can go, how tall they can be and how far they sit from property lines and other signs. We check the rules for your site during the survey.
Why do pylon signs need engineering?
They have to stand up to South Florida hurricane winds. Building departments generally require signed and sealed structural drawings for the foundation and structure.
Can you replace just the faces on my existing pylon?
Yes. Face and tenant-panel replacements are common and usually simpler than a new sign. A permit may still be needed, and we handle it.
Do you install pylons built by other companies?
Yes. We install for sign companies and general contractors. See sign installation and our national sign partner program.
How do I start?
Call 305-500-9313 or request a site survey with your address and a site photo.
Request a site survey
Tell us about your sign and location and we will schedule a site survey or follow up with next steps. Prefer to talk? Call 305-500-9313.
Corporate Signs Inc. | 5960 NW 99th Ave - Bay 8, Doral, FL 33178 | 305-500-9313 | [email protected] | Licensed and insured | Serving South Florida since 1995
Send us the site address, photos and any drawings you already have.
Request a Site SurveyOr call 305-500-9313




